Relax A Mist Steam Generator JR3 Electronic Drain Valve - Matt Black

Relax-A-Mist® Steam Equipment Specifications:

JR-3-EDV- MAX 260 CUBIC FEET

STEAM GENERATOR SELECTION
To select the correct size of steam generator, add the cubic footage of the shower
with the appropriate adjustment to determine the calculated cubic footage:
1. Length x Width x Height = CUBIC FOOTAGE. Do not deduct for seati ng.
2. Add appropriate adjustment to account for heat loss through materials:
Acrylic or Fiberglass ............................................................No adjustment
Ceramic Tile, ¼” thick, or Cultured Marble ..................................... + 30%
Ceramic Tile, ⅜" thick or thicker .................................................... + 100%
Glass or Glass Block wall ................................................................. + 15%
Natural Stone or ½" thick material ................................................. + 100%
Steam lines over 25 feet (insulate heavily) ..................................... + 25%
Cast Iron Tub ................................................................................... + 25%
Exterior walls subject to freezing .................................................... + 30%
3. Select the generator that corresponds to your calculated cubic footage:
Model Number JR-1 JR-2 JR-3 JR-4
Maximum Calculated Cubic Feet 90 175 260 375
4. Line voltage must be specifi ed when ordering. Units available in 240 or 208
Volts, 1 Phase. Single family dwellings usually have 240 Volts AC while
condominiums usually have 208 Volts AC. Note: Use Copper Wire Only.
DISCLAIMER:
The above informati on represents suggesti ons only. Each steam room is unique. Relax-A-Mist® manufactures steam generators
only and therefore cannot warrant informati on given regarding steam room materials or constructi on techniques. Final
selecti on of the steam room temperature setti ng and the durati on of stay, is at the discreti on of the operators or owners.
ELECTRICAL REQUIREMENTS
Breaker/Fuse Size 40 Amps
Power Supply Wire Size #8 AWG
Watt s 6,000
Hz 60
Volts 240
Phase 1
* Must use supply wires suitable for 90o C
* Wire size may diff er depending on
temperature rati ng; consult with certi fi ed
Electrician.
PLUMBING REQUIREMENTS
Steam Lines Required* 2
Steam Line Size ½”
Water Supply Size** ½”
Drain Line Size*** ¾”
* Steam lines must be type ‘L’ rigid copper.
** Water supply is reduced to factory
supplied ⅜” connecti on.
*** Drain line is opti onal; if drain plug
is removed, shut-off valve MUST be
installed.
DIMENSIONS & WEIGHT
Length 16”
Width 12 ½”
Height* 9”
Weight 30 lbs
* Height is measured from bott om of unit to
the top of the union on the steam line.
QUALITY STEAM BATH EQUIPMENT
RELAXA MIST
®
6909 Antrim Avenue, Burnaby B.C. Canada V5J 4M5 Tel: 604-437-4717 or 1-800-Y-U-STEAM (1-800-987-8326) Fax: 604-437-5776
Email: steamman@relax-a-mist.com Website: www.relax-a-mist.com
SPECIFICATION SHEET
Relax-A-Mist® Steam Equipment Specifications
OPTIONAL ACCESSORIES
Time & Temperature Control
Electronic digital control with time and
temperature settings and handheld remote.
Drain Valve - Manual, ¾”
Drain Valve - Automatic, Electronic, ¾”
Steam Nozzle Guard, Acrylic
Steam Nozzle Drip Tray, Acrylic
*See Pricing Guides for additional accessories
and options
AVAILABLE FINISHES
Chrome
Brushed Nickel
24K Gold
Venetian Bronze
*Custom finishes may be ordered, please enquire
for details and pricing.
Supply and install one only CSA approved, pre-tested, automatic, electric, Relax-A-Mist® steam bath generator complete with
internal switching and digital control. See our pricing guides for part numbers and available finishes and controls.
1. The steam unit shall be a Relax-A-Mist® model JR-3
rated at 240 Volts AC, 60 hz, 1 Phase power.
2. The appliance shall be assembled and wired at the
factory, ready for the connection of power supply and
ground wires, control switch, water supply, steam line
piping, and any optional accessories.
3. The appliance shall be supplied complete with:
a) A 16 gauge powder coated steel outer jacket with:
▪ 1 inch of insulation surrounding the inner copper
boiling tank
▪ separate boiling tank, supply voltage and low
voltage compartments
▪ bonding to a copper grounding lug
b) The water boiling tank is to be:
▪ made of a non-ferrous copper material that is
electrolytically compatible with copper piping,
and the electric heater element fastened to the
steel outer jacket with legs
▪ a dual chamber for boiling and controlling the
water level
▪ bonded to a copper grounding lug
c) A 240 Volt copper sheath immersion heater
element, mounted in a copper pan assembly with
an element thermal protection device.
e) An electronic water level control device
with no moving parts inside the boiling tank
compartments.
f) A low water heater cutoff.
g) One only, water resistant digital timer switch
(plug and play) with numeric display, maximum
60 minutes, counts down to 1 minute and
automatically turns off. Includes an 22 gauge solid
copper wire plug and play cord set, bonded to a
copper grounding lug.
h) All controls protected by a transformer and 1 amp
fuses.
i) All non-current carrying metal parts are bonded to
a copper grounding lug.
j) Two plated zinc die cast steam nozzles with a
minimum ½ inch diameter flow-through capacity
and a ¾ inch discharge capacity; complete with a
collar that fits the escutcheon to accommodate
various brass nipple installation lengths. The
nozzles include an aromatic scent well and diffuser
passage.
k) Two plated zinc die cast escutcheons, sized to
accommodate the steam nozzle adjustment collar.
l) A non-pressurized safety flow steam system.
m) A ¾ inch drain line for the optional connection of a
manual or electric drain valve.
n) Two brass unions to connect steam piping.
o) One hose connection: brass union to ⅜” copper
tubing to connect the water supply.
p) Complete written installation instructions with
diagrams.